ARTURO CP-30 is the compact version of the ARTURO air purifier: fan, pre-filters, plasma cell and activated carbon in a single stainless steel body.
Compact version
The machine is placed between the hood and the discharge. Inside are the fan, the inverter and the control panel, already assembled.
The data on this page come from technical dossier ETC-DT-ARTURO-CP-001 Rev. 1.0 · 04/10/2026.
ARTURO CP-30 is documented by a technical datasheet, an installation, use and maintenance manual, a risk assessment and a treatment analysis. The technical datasheet can be downloaded freely from this page; the manual can be read online and downloaded after signing in.
ETC-DT-ARTURO-CP-001 Rev. 1.0 · 04/10/2026Sizing
The air flow decides the model
ARTURO CP-30 covers air flows up to 3,000 m³/h, with an operating range from 2,400 to 3,000 m³/h. For air flows up to 1,500 m³/h there is ARTURO CP-15. The final check must be made on the actual system.
ETC Group · Air Filtration Technologies
ARTURO CP-30
Compact unit for fumes and odoursExtracts, treats and discharges in a single stainless steel body.
For catering hoods and workstations, dental and goldsmith laboratories and the chemical industry, within the limits of use set out in the manual.
- Air flow
- 3,000 m³/h
- Structure
- AISI 304 stainless steel
- Power supply
- 220 V · 50 Hz
- Weight
- 150 kg
Manual
Installation, use and maintenance manual
One manual for ARTURO CP-15 and ARTURO CP-30: safety, installation, commissioning, maintenance, washing of the cell and pre-filters with the detergents, troubleshooting, spare parts and disposal.
The problem
Smoke, grease aerosol and odorous compounds
Cooking vapours carry greasy particulate and odorous compounds. If they are not treated, they settle in the ducts and reach the discharge.
Grease settles on the inner surfaces of the extraction system.
Untreated particulate reaches the fan and fouls it.
The remaining odorous fraction can be smelled outside.
How it works
Three treatment stages and a fan
The air passes through the pre-filters, the electrostatic plasma cell and the activated carbon filter. The fan pushes it towards the discharge.
They hold back the coarser grease
High-density glass wool filters with electrostatic effect. They must always be fitted: without pre-filters the carbon saturates early.
It charges and collects the particles
The 200 W cell holds grease and smoke on its plates. The oxidising action of cold plasma also works on odours and volatile organic compounds.
It reduces residual odours
Activated carbon filter 4V class F9, 592 × 592 × 292 mm, downstream of the cell. It works on air from which the grease has already been removed.
Extraction
Fan and inverter are on board
The air flow is set with the inverter during commissioning, according to the pressure drops of the actual system.
The fan is an EYNGL 1.5 centrifugal fan in AISI 304 stainless steel, 1.5 kW, 3,520 m³/h at 640 Pa, three-phase motor. The inverter is a Toshiba VF-S15.
Filter pack
Pre-filters, plasma cell and carbon
In the CP-30 the components have these sizes.
At a glance
6 kg
3,520 m³/h at 640 Pa
70 dB(A)
The system air flow must stay within the operating range of the model. Outside the range the cell does not work at the correct velocity.
Technical data
ARTURO CP-30
The data are those of the technical dossier. The other model has its own data, see its page.
| Model | Air flow | Fan | Motor power supply | Inlet / outlet | Inverter | W × H × D | Weight |
|---|---|---|---|---|---|---|---|
| ARTURO CP-30 | 3,000 m³/h (2,400–3,000) | EYNGL 1.5 stainless · 1.5 kW · 3,520 m³/h at 640 Pa | three-phase | Ø200–250 / Ø200–250 mm | 1.5 kW · 230 V single-phase → three-phase | 850 × 1,250 (+600 fan) × 640 mm | 150 kg |
Noise 70 dB(A) · AISI 304 structure · 220 V, 50 Hz power supply with earthing (earth resistance < 2 Ω) · purification efficiency ≥ 90% at nominal air volume · cell power 200 W · equipment resistance < 150 Pa.
Installation
Between the hood and the discharge, with access for maintenance
It is installed indoors, or outdoors with a suitable cover that is not included in the supply.
- Vertical installation, with body inclination below 2°.
- Inspection space of more than 0.8 m on the side of the filter access door.
- Brackets and supports for 150 kg, with a 50% margin.
- Air velocity in the duct as low as possible, preferably below 19 m/s.
Anti-vibration joint between fan and machine. Flanges sealed with butyl tape or neutral silicone: every leak is a filter bypass.
Limits of use
Conditions stated in the manual
Outside these limits performance drops and the machine can be damaged.
+10 / +40 °C ambient · 55 °C max treated gases · < 20 mg/m³ particulate · humidity 20–90% · altitude < 1,000 m.
Compliance
Machine documentation
The manual contains the risk assessment, the reference standards and the template of the EC declaration of conformity.
- Low Voltage 2014/35/EU
- Electromagnetic Compatibility 2014/30/EU
- UNI EN ISO 13857:2020 · CEI EN 60204 · CEI EN 60335
- Risk assessment according to UNI EN ISO 12100
- ISO 16890 filter classification
Whether the installation is permitted also depends on local regulations. Design, permits and dealings with the authorities remain the responsibility of the client and of qualified technicians. ETC Group acts as supplier only.
Request an assessment
Tell us the air flow and the type of cooking
With these data we check which model is suitable and how to connect it to the system.
This website uses artificial intelligence tools to support texts, images and virtual assistants; research, projects, solutions and inventions are the result of human intellectual work. Automated responses are provided for informational purposes only and are not binding.